• <track id="9ridc"><ruby id="9ridc"></ruby></track>
    1. <tr id="9ridc"><label id="9ridc"></label></tr>
      <tr id="9ridc"><label id="9ridc"></label></tr>
    2. 產品展示
      PRODUCT DISPLAY
      產品展示您現在的位置: 首頁 > 產品展示 > 臺灣儀鼎PICOTEST > PICOTEST測試訊號轉換器 > J2101A中國臺灣儀鼎PICOTEST專業測試訊號轉換器

      中國臺灣儀鼎PICOTEST專業測試訊號轉換器

      更新時間:2020-03-31
      瀏覽次數:1164
      簡要描述:

      中國臺灣儀鼎PICOTEST專業測試訊號轉換器J2101A Low band corner frequency 達10Hz,可支援一般離線式電源供應器(off-line power supplies)之測量,45MHz之超高頻寬,足以對應目前及未來Z先進之穩壓器量測需求,超高頻寬,可達23 Octave,優異精確的低失真表現,5Ω終端,對待測電路的影響降至Z小,包括衰減功能來確保小信號的測量正確性

      在線咨詢

      中國臺灣儀鼎PICOTEST專業測試訊號轉換器

      J2101A Injection Transformer 10Hz~45MHz 

       
       
       
      iconLow band corner frequency 達10Hz,可支援一般離線式電源供應器(off-line power supplies)之測量
      icon45MHz之超高頻寬,足以對應目前及未來zui先進之穩壓器量測需求
      icon超高頻寬,可達23 Octave
      icon優異精確的低失真表現
      icon5Ω終端,對待測電路的影響降至zui小
      icon包括衰減功能來確保小信號的測量正確性
      icon詳細規格
      中國臺灣儀鼎PICOTEST專業測試訊號轉換器
      Product Information

      The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.

      The usable bandwidth of an injection transformer is generally significantly greater than the 3dB frequency limits. This is because the transformer itself is outside of the measurement, leading many to incorrectly believe that the transformer is a non-critical element.

      The bandwidth of the transformer is strongly related to the terminating impedance. The most network analyzers provide a 50 Ohm oscillator source impedance. Assuming this impedance the optimal termination resistor is 5 Ohms. This significantly attenuates the injection signal, which is generally beneficial, as a common error in Bode measurements is using a signal which is too large, and therefore not a small signal measurement. An added benefit of this low value is that it can generally be left in circuit at all times, simplifying the connection to the network analyzer without appreciably impacting the output voltage of the circuit being tested.

      Detailed Specifications:
       
      Performance at -10dBm input level
      CharacteristicRating
      DCR 
      Ratio1:1
      Termination Impedance5 Ohms
      Nominal 3dB Bandwidth10Hz ~ 45MHz
      Isolation Voltage600V
      Isolation Capacitance150pF@1KHz
      DC Current10mA
      Temperature Range0 ~ 50°C
      Maximum Altitude6000 Ft
      聯系方式
      • 服務熱線:

        4009023318

        13913158248

        15295666126

      • 公司電話:

        0512-66315386

      • 公司傳真:

        0512-66315383

      在線客服
      • 技術支持:
      • 產品咨詢:

      av经典动态高潮gif图无码
    3. <track id="9ridc"><ruby id="9ridc"></ruby></track>
      1. <tr id="9ridc"><label id="9ridc"></label></tr>
        <tr id="9ridc"><label id="9ridc"></label></tr>
      2. 掃一掃訪問手機站掃一掃訪問手機站
        訪問手機站